What are your ideas concerning How to Install a Bathtub?
Mounting a bathtub isn't specifically rocket science, however it does call for solid plumbing, woodworking, and often, tiling abilities. Changing an old bathtub with a brand-new one is also a moderately hard project. If the old tub is conveniently accessible, the job can relocate quickly; if you have to open up a wall surface to remove the old tub and also position the new tub, the job is much harder. In either situation, the task is within a residence handyman's skills, although you will require an assistant to move out the old bathtub and also set in the new one. Make certain you have actually certified on your own for the job as well as fit trying it. Rather than working with a service provider to take control of a halfway-completed task, it is far better to consider employing one before you begin. Chances are you may need a professional plumber to make tube links.
This post will certainly aid you set up a brand-new tub in your shower room if you have actually currently gotten a new tub and don't need to transform the setup of your previous water pipelines.
Your devices and material checklist should comprise the following:
Getting ready for the Setup
First of all, the supporting frame supplied with the bath ought to be fitted (if required) according to the producer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to see to it that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets device to avoid stress on the tub.
Fit the flexible tap adapters to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet via the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you use all of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be suited its final setting.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your setup, then the first thing you must do is detach the water supply. After doing so, activate the taps to drain pipes any water staying in the system. The process of eliminating the existing faucets can be rather bothersome because of the limited access that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the taps. Have a towel ready for the staying water that will certainly come from the pipelines. Once the supply pipes have actually been removed, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from turning during this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any old sealing substance.
Prior to proceeding to fit the brand-new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Mounting the Bathtub
Utilizing both wood boards under its feet, place the bathtub in the needed setting. The wood boards are helpful in evenly spreading out the weight of the tub over the location of the boards instead of focusing all the weight onto four little factors.
The following objective is to ensure that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the bath tub till the level reads level.
To install taps, fit the bottom of the furthest versatile tap port to the proper supply pipeline by making a compression sign up with; after that do the exact same for the various other faucet.
Activate the water and also examine all joints and also brand-new pipework for leakages and also tighten them if essential. Load the bath tub as well as additionally examine the overflow outlet and the normal outlet for leaks.
Finally, fix the bath paneling as described in the manufacturer's instruction manual. Tiling as well as sealing around the bathtub ought to wait until the bathtub has been used at least when as this will certainly settle it into its final position.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end provides a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making certain that the washing machines are in place in between the faucet as well as the sink. Secure the faucet in position with the producer provided backnut. As soon as the faucet is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical tap adapters. The previous kind must be connected to the faucet finishes first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the location where the bath satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to split a rigid seal, creating the water to permeate the wall in between the bath and also the tiling, resulting in issues with dampness and also possible leakages to the ceiling below.
You can choose from a range of coloured sealants to assimilate your fixtures as well as fittings. They are offered in tubes and cartridges, as well as are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bathtub with water before securing, to allow for the motion experienced when the tub is in usage. The sealant can split rather early if you do not think about this movement before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly readily available on the market. It is suggested to fit the tiles using waterproof or water-proof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed our post on Tools You Need to Install a New Bathtub . Thank you for spending some time to read through our article. Loved our post? Please share it. Let someone else check it out. Thank you so much for your time invested reading it.
Schedule Free Estimate